In addition to the brand-new tanker and pump truck, our company also supplies used tanker and pump truck. According to the customer's request, now we provide the tank car refitting business, that is, the customer has the automobile chassis, our factory provides the concrete mixing tank and the corresponding hydraulic system's installation, saves the cost for the user. Determination of mixing capacity of concrete mixing tank truck.

这点很重要，要按客户提供车的载重来确定，车的吨位数确定了你安装搅拌罐容量的多好，混凝土搅拌罐车选择搅拌筒的布置形式

This is very important. It should be determined according to the load of the truck provided by the customer. The tonnage of the truck determines how good the capacity of the mixing tank you install. The concrete mixing tank truck chooses the layout of the mixing drum

三种布置形式，搅拌筒在汽车底盘上。出料口筒口朝向汽车的尾部后方倾斜放置，也是常见的一种;是搅拌筒向前倾斜，在搅拌筒前方装料和卸料;还有一种是整个上装可以回转(或者倾斜)的斜置搅拌筒。其中以搅拌筒后倾布置的结构形式多。一般设计时选用搅拌筒后倾布置。

There are three kinds of arrangement, the mixing drum is on the automobile chassis. It is also a common type that the outlet barrel is inclined toward the rear of the vehicle; the mixing drum is inclined forward to load and unload in front of the mixing drum; there is also a kind of inclined mixing drum with the whole upper loading that can be rotated (or tilted). Among them, there are many structural forms of backward inclined mixing drum. Generally, the mixing drum is arranged backward in design.

小型混凝土搅拌罐车的阀体检修在整个工程作业中也是重要的，做好基本的检修我们的工作才能正常进行。将一张#600的砂纸置于ATF油中，浸泡约30分钟。小心地敲击阀体，使卡滞的阀杆从阀腔孔中落下。可能有必要使用一把小螺丝刀，将其撬出。

The valve body maintenance of small concrete mixing tank truck is also important in the whole project operation. Only by doing a good job of basic maintenance can our work be carried out normally. First, place a piece of sandpaper of ා 600 in ATF oil and soak for about 30 minutes. Carefully tap the valve body to allow the stuck stem to fall out of the cavity bore. It may be necessary to lever it out using a small screwdriver.

简析小型混凝土搅拌罐车的检修

Maintenance of small concrete mixing tank truck

使用螺丝刀时，小心不要划伤阀孔。单向阀杆是否有摩擦痕迹。使用ATF油浸泡过的#600砂纸，打磨阀杆上的毛刺，然后在溶剂中清洗阀杆并用压缩空气吹干。卷起半张ATF油浸泡过的#600砂纸，将其插入卡滞阀杆的阀孔中。轻轻扭动砂纸，使砂纸松卷，紧密贴合在阀孔表面，然后边推拉，边扭卷砂纸，打磨阀孔。抽出#600砂纸。在溶剂中清洗整个阀体，然后用压缩空气吹干。在阀杆表面涂ATF油，然后将其落入阀孔中。阀杆应能靠自重落入阀孔底部。否则，重复步骤4，重新测试。如果阀杆仍然卡滞，则更换阀体。

When using a screwdriver, be careful not to scratch the valve bore. Check whether there are friction marks on the one-way valve stem. Grind the burrs on the valve stem with ා 600 sandpaper soaked in ATF oil, then clean the valve stem in solvent and dry it with compressed air. Roll up half a piece of ා 600 sandpaper soaked in ATF oil and insert it into the valve hole with stuck valve stem. Gently twist the sandpaper to make the sandpaper loose and tightly fit on the surface of the valve hole. Then, while pushing and pulling, twist the sandpaper to polish the valve hole. Draw out 600 sandpaper. Clean the entire valve body in solvent and blow dry with compressed air. Coat the surface of the valve stem with ATF oil and drop it into the valve hole. The valve stem should be able to fall into the bottom of the valve hole by its own weight. Otherwise, repeat step 4 and retest. If the stem is still stuck, replace the valve body.

取出小型混凝土搅拌罐车阀杆，用溶剂清理阀杆和阀体。用压缩空气吹干所有零件，然后用ATF油作为润滑剂，重新组装。

Take out the valve rod of small concrete mixing tank truck and clean the valve stem and valve body with solvent. Dry all parts with compressed air and reassemble with ATF oil as lubricant.

本文由小型搅拌机友情奉献.更多有关的知识请点击:https://www.zishangliaojiaobanji.cn我们将用真诚的态度.为您提供为的服务.更多有关的知识我们将会陆续向大家奉献.敬请期待.

This article is dedicated by the small mixer. For more information, please click: https://www.zishangliaojiaobanji.cn We will be sincere attitude. To provide you with a comprehensive service. More relevant knowledge we will continue to contribute to you. Please look forward to