If the operation is completed, then the small blender will be idle in the warehouse, at this time many people will think that there will be no problem, but not, small blender idle to prevent rust and deformation!

　　小型搅拌机运行后，必须清除外部污垢，清洗工作机构内的饲料和杂物，必要时用水或油清洗，所有润滑部位必须清洗干净并重新润滑。清洁搅拌机后，操作人员还应在搅拌机上涂抹油或贴纸，以减少与空气接触的设备氧化的机会。我建议将搅拌机放在凉爽、干燥、通风的房间内。

　　After the small mixer runs, it must remove external dirt, clean the feed and debris in the working mechanism, clean with water or oil if necessary, and all lubricating parts must be cleaned and re-lubricated. After cleaning the mixer, the operator should also apply oil or stickers to the mixer to reduce the chance of oxidation of equipment in contact with air. I recommend keeping the blender in a cool, dry, ventilated room.

　　复杂精密的设备应放置在室内阴凉、干燥、通风的地方。简单的设备可以露天存放，但应放在高处、干燥、无阳光直射的地方。它可以覆盖一个棚子和所有与地面直接接触的部分。用木板或砖块支撑，重新刷掉掉下来的保护漆。

　　Complex and precise equipment should be placed in a cool, dry and ventilated place indoors. Simple equipment can be stored in the open air, but should be placed in a high, dry place without direct sunlight. It can cover a shed and all parts that have direct contact with the ground. Support it with wood or brick and repaint the protective paint that has fallen off.

　　小型搅拌机的弹簧。传动带。长柄。由于长期受力或放置不合理，零部件会发生塑性变形，因此在搅拌机框架下应增加适当的支撑点，以减少搅拌机负荷。此外，轮胎、播种管等拆下的零配件应妥善保管，防止挤压变形。

　　Springs for a small blender. Belt. Long handle. Due to long-term stress or improper placement, parts will have plastic deformation, so appropriate support points should be added under the frame of the mixer to reduce the load of the mixer. In addition, tires, seeding pipes and other removed parts should be properly kept to prevent extrusion deformation.

　　对于长期停放的小型搅拌机，应建立登记卡，详细记录机器和工具的技术状况、附件、备件和工具。如果没有仓库，当机器停放在室外时，应将电机、传动带等易丢失的部件取出，标记并存放在室内。

　　A registration card shall be established for the small mixer that is parked for a long time to record the technical status, accessories, spare parts and tools of the machine and tools in detail. If there is no warehouse, when the machine is parked outdoors, the motor, transmission belt and other parts that are easy to lose should be taken out, and the marks should be stored indoors.

　　如果再次使用的话，就要做好开机前的准备工作，比如：检查传动离合器和制动器是否灵活可靠，钢丝绳是否损坏，履带轮是否完好，周围是否有障碍物及各部位润滑情况等;开机后，要时刻注意搅拌机各部分运转是否正常。 停机时要经常检查搅拌机的叶片是否弯曲，螺丝是否被敲落或松动。

　　If it is used again, it is necessary to do the preparatory work before the boot, such as: check whether the transmission clutch and brake are flexible and reliable, whether the wire rope is damaged, whether the track wheel is intact, whether there are obstacles around and the lubrication of various parts; After starting the machine, pay attention to the normal operation of all parts of the blender. Check whether the blades of the mixer are bent or whether the screws are knocked off or loose when the machine is stopped.

　　以上是小型饲料搅拌破碎机与您分享的所有内容。这对你有帮助吗？如果您还想知道什么，请点击https://www.zishangliaojiaobanji.cn网站进行留言。

　　Above is the small feed mixing crusher to share with you all the content. Does that help you? What if you also want to know, please click https://www.zishangliaojiaobanji.cn to leave a message.