小型搅拌机电机为什么会打齿？主要原因是电机的传动功率不均匀，导致电机扭矩与齿轮转速输出力不匹配，造成敲齿。下面来详细讲讲内容吧。

Why do small blender motors gear? The main reason is that the transmission power of the motor is uneven, resulting in the mismatch between the motor torque and the gear speed output force, resulting in tooth knocking. Let's talk about the content in detail.

搅拌机的地面不平整，搅拌机的搅拌筒跳动严重，电机主轴的传动与齿轮传动的传动不在同一轴线上，所以很容易打齿；

The ground of the mixer is uneven, the mixing drum of the mixer jumps seriously, and the transmission of the motor spindle and the gear transmission are not on the same axis, so it is easy to beat teeth;

小型搅拌机的电机或搅拌筒还在转动，手动停止小型搅拌机的电机或滚筒，容易打齿；

The motor or mixing drum of the small mixer is still rotating. Manually stopping the motor or drum of the small mixer is easy to beat teeth;

搅拌机运转前，启动电机并将电机的开关电路虚接，造成电机运转不正常，电机与齿轮接触异常，造成电机内部齿轮击败；

Before the operation of the mixer, start the motor and falsely connect the switch circuit of the motor, resulting in abnormal operation of the motor and abnormal contact between the motor and the gear, resulting in failure of the internal gear of the motor;

由于电机内齿轮磨损严重，啮合间隙大，启动搅拌机小电机工作，导致电机驱动力传递异常，形成齿；

Due to the serious wear of the internal gear of the motor and large meshing clearance, start the small motor of the mixer to work, resulting in abnormal transmission of motor driving force and formation of teeth;

搅拌机的齿齿只有在非正常运行情况下才容易出现。建议您按要求使用搅拌机，以免出现敲齿等异常损坏。

The teeth of the mixer are easy to appear only under abnormal operation. It is recommended that you use the mixer as required to avoid abnormal damage such as tooth knocking.

所以要避免此类问题的出现就要做好相关的维护工作，比如：

Therefore, to avoid such problems, it is necessary to do relevant maintenance work, such as:

搅拌机所选用的电机、减速机必须与安装图纸规定的一致。搅拌机应由经过培训的合格人员进行操作。若搅拌机所选用的减速机为外置润滑时，必须要先启动减速机的润滑系统15分钟左右，再开启搅拌设备。

The motor and reducer selected for the mixer must be consistent with those specified in the installation drawing. The mixer shall be operated by qualified personnel. If the reducer selected by the mixer is external lubrication, the lubrication system of the reducer must be started for about 15 minutes before starting the mixing equipment.

若油泵发生故障时，搅拌电机必须停止工作，否则将损坏减速机和电机。定期观察记录电机的电流值，测减速机、电机的温度。电机上的防尘罩要定期清理，保证电机良好散热。

If the oil pump fails, the mixing motor must stop working, otherwise the reducer and motor will be damaged. Regularly observe and record the current value of the motor and measure the temperature of the reducer and motor. The dust cover on the motor shall be cleaned regularly to ensure good heat dissipation of the motor.

正常情况下，搅拌设备运行平稳；电机电流稳定,电流值一般在额定电流值的80%左右；减速机、电机无杂音且减速机温升不超过60℃。

Under normal conditions, the mixing equipment operates stably; The motor current is stable, and the current value is generally about 80% of the rated current value; The reducer and motor shall be free of noise, and the temperature rise of the reducer shall not exceed 60 ℃.

停止搅拌机时，先停止主电机，再停止润滑系统。轴承箱要定期润滑，滚动轴承使用固定年限必须更换。减速机、电机可参照其说明书进行操作、维护。

When stopping the mixer, first stop the main motor and then stop the lubrication system. The bearing housing shall be lubricated regularly, and the rolling bearing must be replaced for a fixed service life. The reducer and motor can be operated and maintained with reference to their instructions.

小型搅拌机电机打齿的原因我们找到了，方法就要按照实际情况来做好预案了，当然还是建议去找维修厂进行修理。更多内容的了解就关注网站www.zishangliaojiaobanji.cn吧！

We have found the reason for the gear beating of the small mixer motor. The solution is to make a plan according to the actual situation. Of course, it is recommended to go to a professional maintenance factory for repair. For more information, please follow the website www.zishangliaojiaobanji.com Cn!