自上料搅拌机减速机漏油分为轴封漏油、端盖与壳体连接处漏油、马达和减速机连接处漏油三种情况，所以，在遇到搅拌机减速机漏油的情况是要分清到底是哪个部位出现漏油，下面具体介绍一下这三种漏油情况。

The oil leakage of the reducer of the self feeding mixer can be divided into three cases: shaft seal oil leakage, oil leakage at the connection between the end cover and the housing, and oil leakage at the connection between the motor and the reducer. Therefore, in case of oil leakage of the reducer of the mixer, it is necessary to distinguish which part has oil leakage. The following details about these three kinds of oil leakage.

一、轴封漏油

1、 Oil leakage of shaft seal

轴封漏油多数是因为使用不当造成减速机划伤或减速机输出轴划伤及异物缠绕所导致的。此时还需要更换轴封或是更换油封，在自上料搅拌机减速机的使用过程中一定要记得及时清理油封处的异物。

The shaft seal oil leakage is mostly caused by gear reducer scratch or gear reducer output shaft scratch and foreign matter winding due to improper use. At this time, it is also necessary to replace the shaft seal or oil seal. During the use of the reducer of the self feeding mixer, remember to clean the foreign matters at the oil seal in time.

二、端盖与壳体连接处漏油

2、 Oil leaks at the connection between the end cover and the housing

这种情况的漏油多数是因为自上料搅拌机减速机连接螺栓松动而造成的，此时需要及时复紧端盖和壳体连接螺栓或更换减速机，更或是更换减速机端盖和壳体间的O型圈。为了避免这种情况的再次发生，平时一定要定期检查螺栓扭力。

This kind of oil leakage is mostly caused by the looseness of the connecting bolts of the reducer of the feeding mixer. At this time, it is necessary to tighten the connecting bolts of the end cover and the housing in time or replace the reducer, or replace the O-ring between the end cover and the housing of the reducer. In order to avoid the recurrence of this situation, always check the bolt torque regularly.

三、马达和减速机连接处漏油

3、 Oil leakage at the connection between motor and reducer

主要是因为马达和减速机在安装时，O型圈的密封不达标。这个时候需要更换马达和减速机连接处的O型圈，检查马达和减速机安装表面是否有划伤。在自上料搅拌机平时使用过程中一定要注意检查马达和减速机安装的螺栓是否有松动，有松动及时调紧。

This is mainly because the O-ring seal of the motor and reducer is not up to standard during installation. At this time, replace the O-ring at the connection between the motor and the reducer, and check whether the mounting surface of the motor and reducer is scratched. During the normal use of the self feeding mixer, pay attention to check whether the bolts installed on the motor and reducer are loose, and tighten them in time if they are loose.

搅拌机减速机还容易出现异响的问题，这个时候就应该做一些检查来找出问题所在，具体检查内容：

The mixer reducer is also prone to abnormal noise. At this time, some inspections should be carried out to find out the problem. Specific inspection contents:

在油位观察窗处检查油位是否正常；检查搅拌机减速机内是否有齿轮油；放出少量油液看是否有发黑变质并校对保养时间；检查搅拌机减速机是否受到过外力冲击。如果在放油的时候发现有大量铁屑，那就是搅拌机减速机内部已经被损坏了，需要更换减速机。

Check whether the oil level is normal at the oil level observation window; Check whether there is gear oil in the mixer reducer; Drain a small amount of oil to see if there is any blackening and deterioration, and check the maintenance time; Check whether the mixer reducer is impacted by external force. If a large amount of iron filings are found during oil discharge, it means that the internal of the mixer reducer has been damaged and the reducer needs to be replaced.

所以说平时要定期的对减速机做好维护保养工作，这样在后期才能更顺利的进行驾驶工作，您关注我们的网站https://www.zishangliaojiaobanji.cn，了解更多的注意事项！

Therefore, the reducer should be maintained regularly so that the driving work can be carried out more smoothly in the later period. You should pay attention to our website https://www.zishangliaojiaobanji.cn , learn more precautions!