搅拌机是工地施工常用到的设备，生产加工效率挺高，所以受到市场的欢迎，不过有些问题还是要多注意的，比如说搅拌机用搅拌轴总成的制作方法是怎样的。下面来分析分析。

　　Mixer is commonly used in construction site equipment, production and processing efficiency is very high, so it is welcomed by the market, but some problems still need to pay more attention to, such as mixer with mixing shaft assembly production method is what. Let's analyze it.

　　搅拌机轴端密封的形式主要靠机械加工精度和装配精度配合来防止搅拌机轴端漏气，这种密封结构主要存在问题，比如加工和装配工艺要求过高，导致制造成本过高。由于靠机械加工精度以及紧密配合来密封，所以对搅拌机的真空负压密封不够，搅拌机轴端漏气现象时有发生。这样会造成搅拌机内的物料因空气不能排尽，搅拌出的物料的质量不稳定。

　　The form of mixer shaft end seal mainly relies on the cooperation of machining accuracy and assembly accuracy to prevent mixer shaft end leakage. This sealing structure mainly has problems, such as high processing and assembly process requirements, resulting in high manufacturing cost. Due to the mechanical processing accuracy and close match to seal, so the vacuum negative pressure seal of the mixer is not enough, the leakage phenomenon of the mixer shaft end often occurs. This will cause the material in the mixer to be unable to exhaust the air, and the quality of the mixed material is unstable.

　　为增加密封效果，可增设多个小密封圈，保证轴套与搅拌轴的结合面不漏气；盘根的设置，不仅可以防止搅拌轴在转动时有气体通过轴套与连接套的接触面，同时也可以防止气体通过连接套与定位环的接触面，盘根可采用聚氨脂盘根，增加压紧盘对盘根的压紧力，盘根受挤变形，内径缩小，外径扩大，从而达到径向密封的作用。

　　In order to increase the sealing effect, a plurality of small sealing rings can be added to ensure that the joint surface of the shaft sleeve and the mixing shaft does not leak; Packing set, not only can prevent when rotating gas on the stirring shaft through the shaft sleeve and connected to the set of interface, but also can prevent gas by connecting the contact area with the locating ring, packing can be used polyurethane packing, increase the pressure plate for packing pressure force, packing by extrusion deformation, narrow diameter, outside diameter expanding, so as to achieve the effect of radial sealing.

　　大密封圈用于连接套与压紧盘之间的密封，防止杂质、空气等进入容纳腔。调节间隙用于补偿盘根的摩损量，随着盘根的摩损，密封性变差，可通过移动压紧盘，相应缩小调节间隙，调整对盘根压紧力以满足密封的目的。压紧盘与轴套配合的套接孔设有向外开口的密封圈容纳槽以容纳复数个具外包骨架的唇形密封圈，唇形密封圈的唇部与轴套触接。

　　The large sealing ring is used to seal between the connecting sleeve and the pressing disc to prevent impurities, air, etc. from entering the accommodating cavity. Adjusting clearance is used to compensate the friction loss of the root of the disk. With the friction loss of the root of the disk, the sealing becomes worse. By moving the pressing disk, the adjustment gap can be reduced accordingly, and the pressing force of the root of the disk can be adjusted to meet the purpose of sealing. The sealing ring opening groove is provided with a sealing ring opening outwards to accommodate a plurality of lip sealing ring with an outer skeleton, and the lip of the lip sealing ring is contacted with the shaft sleeve.

　　在定位环与自上料搅拌机搅拌缸体的结合面涂覆粘结密封层后，定位环与搅拌缸体通过螺钉连接，固定。粘结密封层可采用玻璃胶等。采用密封圈、盘根等密封，降低加工和装配工艺要求，提高加工、装配效率，节约制造成本。密封，避免漏气，保证搅拌机内真空负压，保证搅拌出物料的质量。

　　After the binding surface of the positioning ring and the mixing cylinder is coated with a bonding seal layer, the positioning ring and the mixing cylinder are connected by screws and fixed. Adhesive sealing layer can be used glass glue. Adopt sealing ring, coil and other seal, reduce processing and assembly process requirements, improve processing and assembly efficiency, save manufacturing cost. Comprehensive seal, avoid air leakage, ensure the mixer vacuum negative pressure, to ensure the quality of the mixed material.

　　搅拌机用搅拌轴总成的制作方法便是以上相关内容了，如果您对于搅拌机有其他的想法或者内容，可以通过网站www.zishangliaojiaobanji.cn联系我们共同分享交流。

　　Mixer with the method of making the stirring shaft assembly is related content, if you have other ideas or content for blender, can contact us through the website www.zishangliaojiaobanji.cn share exchange.