小型搅拌机是比较常用的设备，它将各种原材料按科学配比加水搅拌均匀，为生产优良砖坯提供的前提条件，我们接下来详细分析下小型搅拌机的结构及各部分的功能。

Small mixer is a commonly used equipment. It will add water to mix various raw materials in a scientific proportion, providing a prerequisite for the production of excellent brick. Next, we will analyze the structure and functions of each part of the small mixer in detail.

1、搅拌缸

1. Mixing cylinder

它是由厚钢片制成“奥米加”形状，而且由特别管状架框承托，这能保证更佳的屈服阻力，端板承托的法兰亦能使缸身得到坚硬及使轴心不偏不歪。缸身亦十分，方便使人进入，其上可根据客户要求装搅拌监察器。门框装有密封橡胶条，可完全防尘。

It is made of thick steel sheets in the shape of "Omega" and supported by special tubular frame, which can ensure better yield resistance. The flange supported by the end plate can also make the cylinder body hard and the shaft center not deflected. The cylinder body is also very safe and convenient for people to enter. The mixing monitor can be installed on it according to customer requirements. The door frame is equipped with a sealing rubber strip, which can completely prevent dust.

2、缸内装有衬板

2. Liner plate is installed in the cylinder

缸内是由件件可螺钉锁紧及互相替换的组件所砌成。它们都是防磨损高铬耐磨合金铸铁制成，其硬度达HRC54.衬板的使用寿命可达40000罐次。生产过程中要及时调整叶片与衬板的间隙(<5mm)，否则会加剧叶片、衬板的磨损。

The cylinder is made of components that can be locked and replaced by screws. They are made of wear resistant high chromium wear-resistant alloy cast iron, and their hardness reaches HRC54. The service life of the lining plate can reach 40000 cans. During the production process, the clearance between the blade and the lining plate shall be adjusted in time (<5mm), otherwise the wear of the blade and lining plate will be aggravated.

3、搅拌臂

3. Mixing arm

搅拌臂由优良合金钢制成，配合得当的拌臂位置可保证达到均匀好的效果。

The mixing arm is made of excellent alloy steel, and the proper mixing arm position can ensure a uniform and good effect.

4、搅拌叶片

4. Mixing blade

叶片是经过科学分析，反复试验而终确定的更佳形状、尺寸、角度以及两轴距，在搅拌过程中保证了搅拌臂、叶片使物料充分地在纵向和横向和上下产生剧烈地搓揉、流动，在短的时间内达到物料均匀拌和之目的。

The blade is a better shape, size, angle and two wheelbase finally determined through scientific analysis and repeated tests. During the mixing process, the mixing arm and blade ensure that the materials can fully rub and flow violently in the longitudinal and transverse directions and up and down, and achieve the goal of uniform mixing of materials in a short time.

5、卸料

5. Unloading

气缸可操作卸料的运行，共分三个停放的位置，包括关，半开及全开，这能立即地把混凝土卸落搅拌输送中。当按下开闸的按钮时，相应的电磁阀便会动作，然后电机转动，料门关闭。由于气缸活塞密封圈的磨损，气缸便会抵消冲程的加速，必要时检查更换密封圈。

The air cylinder can operate the unloading operation, which is divided into three parking positions, including off, half open and full open, which can immediately unload the concrete during mixing and transportation. When the brake opening button is pressed, the corresponding solenoid valve will act, then the motor will rotate and the material door will close. Due to the wear of the cylinder piston seal ring, the cylinder will offset the acceleration of the stroke. If necessary, check and replace the seal ring.

6、轴的密封

6. Sealing of shaft

由于黄胶密封及轴端会磨损及损坏，因此泥浆将会渗漏，在这种情况下需要调整或更换轴端密封件此机仍可继续操作(轴承分隔及远离密封)。

The yellow glue seal and shaft end will be worn and damaged, so the mud will leak. In this case, it is necessary to adjust or replace the shaft end seal. The machine can still continue to operate (bearing separation and away from the seal).

7、减速机

7. Reducer

电机与减速机之间的动力传送，是靠“V”形三角皮带带动实现的。同心动力的连接，可使轴同步地旋转。

The power transmission between the motor and the reducer is driven by a V-shaped V-belt. The connection of concentric power can make the shaft rotate synchronously.

8、搅拌系统

8. Mixing system

搅拌形式是靠两水平轴以相反方向转动而成的，在两轴之上，设有相同数量的拌臂，并作螺旋状排列。拌臂的特别形状，它们起交错地旋转，如此的搅动，在短时间内，能保证有好的品质效果，因为在不同重量或体积下，它能避免分隔地聚集而成不平均状态。

The mixing form is formed by rotating two horizontal shafts in opposite directions. The same number of mixing arms are arranged on the two shafts in a spiral manner. The special shape of the mixing arm. They rotate alternately. Such agitation can ensure a good quality effect in a short time, because under different weights or volumes, it can avoid the uneven state caused by the separated aggregation.

通过以上介绍，我们可以清晰的了解小型搅拌机是如何工作的，它对原材料的处理起着关键性的作用，更多相关内容就来我们网站https://www.zishangliaojiaobanji.cn进行咨询吧！

Through the above introduction, we can clearly understand how the small mixer works. It plays a key role in the processing of raw materials. More relevant information can be found on our website https://www.zishangliaojiaobanji.cn Consult!