任何设备在使用前都是需要进行检查的，其中也包括了施工使用的自上料搅拌机，但是对其进行检查时并不是盲目的进行，而是根据一些原则去检查，下面来讲讲有关原则点。

Any equipment needs to be inspected before use, including the self feeding mixer used in construction. However, the inspection is not conducted blindly, but according to some principles. Here are some principles.

逐台检查锥形反转出料搅拌机的搅拌筒进料口径向跳动、端面跳动和搅拌筒大齿圈与小齿轮啮合情况，均应达到规定，不达标准的要及时处理。

One by one, check the feeding diameter run out and end face run out of the mixing drum of the conical reverse discharge mixer, and the meshing between the big gear ring and the pinion of the mixing drum, which shall meet the requirements. If it fails to meet the standards, it shall be handled in time.

逐台检查搅拌机的搅拌筒轴端密封部位，供油系统供油是否通畅。

Check the sealing part of the mixing drum shaft end of the mixer one by one, and whether the oil supply of the oil supply system is smooth.

逐台检查搅拌机的铲片与底衬板或侧衬板之间的间隙。

Check the clearance between the shovel blade of the mixer and the bottom lining plate or side lining plate one by one.

逐台测定供水系统购供水误差，供水量变动误差和供水时间，并应达到规定。

The water supply error, water supply variation error and water supply time of the water supply system shall be measured one by one and shall meet the requirements.

自上料搅拌机应逐台进行空运转和110%额定载荷试验（可加当量重块），应达到规定。

The self loading mixer shall be subject to idling and 110% rated load test one by one (equivalent weight can be added), which shall meet the requirements.

总之先容易的问题，再更难的问题。不要一开始就陷入困境。先检查外露、易触及、易拆卸的部位，再检查难以触及、易拆卸的部位。检查搅拌机常见故障部位，可以快速确定故障部位，省时省力。

In short, we should first solve the easy problems, and then solve the more difficult problems. Don't get into trouble at the beginning. First check the exposed, accessible and dismountable parts, and then check the hard to reach and dismountable parts. Check the common fault parts of the mixer, which can quickly determine the fault parts and save time and effort.

这里的“静态”是指未启动时的静态；“动态”是指发动机启动后的工作状态。切勿盲目启动汽车，在启动汽车前做好必要的检查和电气性能测试（看是否有漏电、点火或短路），以确保搅拌机的。

"Static" here refers to the static state when it is not started; "Dynamic" refers to the working state after the engine is started. Do not start the car blindly. Before starting the car, do the necessary safety inspection and electrical performance test (to see if there is leakage, ignition or short circuit) to ensure the safety of the mixer.

停电是常见故障之一，所以当电气部分出现故障时，应检查电源部分。一般然后特殊。先检查一般故障，再检查特殊故障。要共性和通用部分的问题，就必须个性和特殊电路的问题。搅拌机分段检查是指在故障诊断过程中，对疑似故障系统进行分步检测和分析，直找到捏合机故障点。

Power failure is one of the common faults, so when the electrical part fails, the power supply part should be checked first. General then special. Check the general fault first, and then check the special fault. To solve the problems of common and general parts, we must solve the problems of individuality and special circuits. Section inspection of mixer refers to the step-by-step detection and analysis of the suspected fault system in the process of fault diagnosis until the fault point of kneader is found.

在对搅拌机进行检测时，要严格按照其检测原则进行，如果不了解可参考上述进行，使搅拌机达到使用规定，从而保证搅拌机的运行效率，促进搅拌机的使用。

When testing the mixer, it should be carried out in strict accordance with its testing principles. If you don't know, you can refer to the above to make the mixer meet the use regulations, so as to ensure the operation efficiency of the mixer and promote the use of the mixer.

以上就是今天为大家分享的关于问题的相关内容，希望对大家能有所帮助，想要了解更多内容可以电话联系我们或者关注我们的网站https://www.zishangliaojiaobanji.cn。

The above is the relevant content about the problem shared for you today. I hope it can help you. If you want to know more, you can contact us by phone or follow our website https://www.zishangliaojiaobanji.cn 。