小型混凝土搅拌机在正常的投料搅拌过程中，搅拌主机出现闷机跳闸现象原因分享及故障处理方法如下：

During the normal feeding and mixing process of small concrete mixer, the reason sharing and troubleshooting methods for the trip of the mixing machine are as follows:

1、原因1·投料过多，引起小型混凝土搅拌机负荷过大

1. Cause 1. Excessive feeding causes excessive load of small concrete mixer

这个要检查整个称料系统是否正常，小型混凝土搅拌机内是否有上盘残余物料以及有无二次投料现象；

This is to check whether the whole weighing system is normal, whether there is any hanging wall residual material in the small concrete mixer and whether there is any secondary feeding phenomenon;

2、原因2·搅拌系统叶片与衬板之间的间隙过大，搅拌过程中，增大了阻力

2. Cause 2. The gap between the blade and the lining plate of the mixing system is too large, which increases the resistance during the mixing process

检查小型混凝土搅拌机叶片与衬板之间的间隙是否在3~8mm；2、衬板厚度是否＞2-3mm，如果衬板厚度不达标，则要及时更换衬板。

Check whether the clearance between the blade and the lining plate of the small concrete mixer is 3-8mm; 2. Whether the thickness of lining plate is ＞ 2-3mm. If the thickness of lining plate is not up to the standard, replace the lining plate in time.

3、原因3·传动皮带太松，使传动系统效率低

3. Cause 3: The transmission belt is too loose, which makes the efficiency of the transmission system low

检查传动皮带的松紧程度是否超过20mm，如是则调整或更换

Check whether the tightness of the drive belt exceeds 20mm. If yes, adjust or replace it

4、原因4·搅拌主机上盖检修开关被振松，引起停机

4. Cause 4. The safety maintenance switch on the upper cover of the mixing host was loosened, causing the shutdown

检查主机上盖开关是否松动并处理

Check whether the safety switch on the upper cover of the host is loose and handle it

5、原因5·减速箱及菊花轴损坏，检查更换即可

5. Cause 5. The reducer and chrysanthemum shaft are damaged. Check and replace them

应当及时进行补救措施。可以对控制台电流表进行监控；对衬板和搅拌机刀片之间的距离进行检查，查看是否超过5厘米。当三角皮带出现老化现象时，应当在及时进行更换，与此同时，还应当检查主轴和联动轴之间是否固定。

Remedial measures should be taken in a timely manner. It can monitor the console ammeter; Check the distance between the lining plate and the mixer blade to see if it is more than 5cm. When the V-belt is aged, it should be replaced in time. At the same time, check whether the main shaft and the linkage shaft are fixed.

对搅拌机的配料系统进行多方位检查，确保未超标情况以及二次投料，对传感器进行检查，使其能够正常运作。在运行搅拌机之前，还应当对主机上盖进行检查，查看是否有松动或者损坏情况。如果有，则应当及时进行更换。关注我们https://www.zishangliaojiaobanji.cn，了解更多相关事项！

The batching system of the mixer shall be inspected in multiple aspects to ensure that it does not exceed the standard and the second feeding. The sensors shall be inspected to ensure that it can operate normally. Before running the mixer, check the upper cover of the main machine to see if it is loose or damaged. If any, it shall be replaced in time. Follow us https://www.zishangliaojiaobanji.cn , learn more about it!