为了减少危险事故的发生，大家在购买设备使用的时候要提前做好准备工作，比如说说明书认真看、去了解注意事项等等，尤其是自上料搅拌车这一类的施工设备更是如此。那么下面我们来了解下搅拌车零部件减震器的使用吧。

　　In order to reduce the occurrence of dangerous accidents, we should prepare for the use of equipment in advance, such as carefully read the instructions, to understand the matters needing attention and so on, especially since the loading mixing truck this kind of construction equipment. So let's learn about the use of shock absorbers for agitator parts.

　　减震器是自上料搅拌车使用过程中的易损配件，减震器工作好坏，将直接影响自上料搅拌车行驶的平稳性和其它机件的寿命，因此我们应使减震器经常处于良好的工作状态。

　　The shock absorber is a vulnerable part in the process of using the self-feeding mixer. The working quality of the shock absorber will directly affect the stability of the self-feeding mixer and the life of other parts. Therefore, we should make the shock absorber often in a good working state.

　　自上料搅拌车在路上行驶10，条件差时停车，用手触摸减震器外壳。这时候可以加入适量的润滑油，然后进行测试，如果外壳发烫，说明自上料搅拌车的减震器内部缺油，应加足量的油；否则，减震器将失效。

　　Since the mixing truck on the road 10 km, the poor condition of the stop, touch the shock absorber shell. At this time, an appropriate amount of lubricating oil can be added, and then tested. If the shell is hot, it indicates that the internal shock absorber of the feeding mixer is short of oil, and a sufficient amount of oil should be added; Otherwise, the shock absorbers will fail.

　　拆下自上料搅拌车减震器，将底环虎钳与上夹具连接，以减少拉动振动杆的次数，这一次它应该是一个稳定的阻力。上拉时阻力应大于下压阻力，或阻力不稳等可能是由于内部挡油板不足或阀件损坏，应修理或更换。

　　Remove the self-loading agitator shock absorber and connect the bottom ring vise to the upper clamp to reduce the number of times the vibrator bar is pulled, this time it should be a stable resistance. When pulling up, the resistance should be greater than the pressure resistance, or the resistance instability may be due to insufficient internal oil baffle or valve damage, should be repaired or replaced.

　　用力按压保险杠，然后松开，如果自上料搅拌车跳2~3次，减震器工作正常。自上料搅拌车运行慢、急刹车时，如果自上料搅拌车振动严重，减振器就会出现问题。

　　Press the bumper hard, and then release it. If it jumps 2~3 times from the loading mixer, the shock absorber works normally. When the self-feeding mixer runs slowly and brakes sharply, if the vibration of the self-feeding mixer is serious, the shock absorber will have problems.

　　另外，在确定自上料搅拌车减振器有故障或失效后，应检查减振器是否漏油或有旧漏油迹象。油封垫圈和密封垫圈断裂损坏，储油缸盖螺母松动。可能是油封和密封垫片损坏失效，应更换新的密封。如仍不能排除漏油，应拔出减震器。

　　In addition, after determining the failure or failure of the shock absorber of the loading agitator, we should first check whether the shock absorber is leaking oil or there are signs of old oil leakage. The oil seal gasket and seal gasket are broken and damaged, and the nut of the oil storage cylinder head is loose. The oil seal and sealing gasket may be damaged and invalid, and a new seal should be replaced. If oil leakage cannot be ruled out, pull out the shock absorber.

　　如果感觉到发夹或不同的重量，进一步检查活塞与气缸之间的间隙是否过大，减震器活塞连杆是否弯曲，活塞连杆是否弯曲。表面和筒体是否有划痕或拉痕。

　　If a hairpin or different weight is felt, further check whether the gap between the piston and cylinder is too large, whether the shock absorber piston rod is bent, whether the piston rod is bent. Whether there are scratches or tensile marks on the surface and cylinder.

　　如果减震器不漏油，请检查减震器连接销、连杆、连接孔、橡胶衬套等有无损坏、脱焊、开裂或脱落。如以上检查均正常，应进一步拆开减震器，检查活塞与气缸的配合间隙是否过大，气缸是否拉紧等等。

　　If the shock absorber does not leak oil, check whether the shock absorber connecting pins, connecting rods, connecting holes, rubber bushings, etc., are damaged, unwelded, cracked or detached. If the above checks are normal, the shock absorber should be further disassembled to check whether the piston and cylinder fit clearance is too large, whether the cylinder is tensioned and so on.

　　自上料搅拌车带有的减震器怎么使用？以上便是相关内容了，如果有故障产生，应该立即去查明原因并修理。如果您不知道原因是什么，可以通过网站www.zishangliaojiaobanji.cn来联系我们，我们将会为您分析。

　　How to use the shock absorbers with the loading agitator? That's it. If something goes wrong, find out the cause and fix it immediately. If you don't know what the reason is, can through the web site www.zishangliaojiaobanji.cn to contact us, we will analysis for you.