1. The hydraulic oil position should be checked before driving every time, and the oil level should be 2-3cm higher than that;

2、整体泵(指没有减速机油箱的)应使用SAE15W～40发动机油;

2. SAE15W-40 engine oil should be used for integral pump (without reducer oil tank);

3、新车使用1～2周，应将副梁和主车大梁的连接螺栓和骑马螺栓复紧，以后每半月紧固一次;

3. When the new car is used for 1-2 weeks, the connecting bolts and riding bolts of the auxiliary beam and the main beam shall be tightened again, and then they shall be tightened once every half month;

4、液压油和减速机油在新车使用100天左右应更换一次。 液压系统存油箱应使用68号耐磨液压油。寒冷地区建议使用46号液压油。 减速机使用90号重负荷齿轮油，建议使用进口壳牌等质量较好的油品;

4. Hydraulic oil and reducer oil should be changed once every 100 days. 68 wear resistant hydraulic oil shall be used in the oil tank of hydraulic system. 46 hydraulic oil is recommended for cold areas. It is recommended to use imported heavy oil such as shell gear reducer 90;

5、新车使用1～2周，应检查托轮座固定螺栓，油泵法兰，传动轴连接螺栓是否松动以后每月紧固一次;

5. When the new car is used for 1-2 weeks, check whether the fixed bolts of the supporting roller seat, the flange of the oil pump and the connecting bolts of the transmission shaft are loose, and then tighten them once a month;

6、整体泵应每月检查一次液压油系统油位， 油位应到该螺栓纹口处;

6. The oil level of the hydraulic oil system of the integral pump should be checked once a month, and the oil level should reach the bolt groove;

7、使用一段时间，应检查进料斗密封皮的完好性，如磨损厉害须及时更换，否则易造成筒口或进料斗磨损;

7. After using for a period of time, check the integrity of the sealing cover of the feeding hopper. If the wear is severe, it must be replaced in time, otherwise it is easy to cause the wear of the barrel mouth or the feed hopper;

8、洗车时应注意高压水流不能对准减速机法兰密封圈处冲洗，以免伤害润滑油脂。

8. When washing the car, it should be noted that the high-pressure water cannot be aligned with the sealing ring of the reducer flange to avoid damaging the lubricating grease.

9、有黄油嘴的地方应每周打一次黄油，保证正常润滑。另外拖轮和滚道结合面处应3～4天加一次黄油，保持正常;

9. Grease the place with grease fitting once a week to ensure normal lubrication. In addition, grease should be added once every 3-4 days at the joint surface of tugboat and raceway to keep it normal;

10、每次收工时要将搅拌筒内外洗干净，保证搅拌筒内无积快。如果在工地卸料时间超过2～3小时回来时也要将搅拌筒内清洗干净;

10. Clean the inside and outside of the mixing drum at the end of each work to ensure that there is no accumulation in the mixing drum. If the unloading time is more than 2-3 hours at the construction site, clean the mixing drum when returning;

11、后操纵手柄每次由搅拌变成卸料或由卸料变成搅拌都要在中间位置停顿一下，在搅拌筒停止转动后再执行下一动作。在手柄扳到极限位置时不能继续用力，防止油泵卡死。

11. Each time the rear control handle changes from mixing to discharging or from discharging to mixing, it should pause at the middle position, and then execute the next action after the mixing drum stops rotating. When the handle is pulled to the limit position, the force cannot be continued to prevent the oil pump from being stuck.

更多的关于 自上料搅拌车的问题或者详细的内容，请进入我们公司的网站：https://www.zishangliaojiaobanji.cn网站中会有很多的内容仅供参考。

For more questions or details about self loading mixer, please visit our website: https://www.zishangliaojiaobanji.cn There will be a lot of content in the website for reference only.